Sale!

    2024 Best SpeedyBee F7 V3 Flight Controller – Unleash Drone Potential

    $63.00

    The SpeedyBee F7 V3 Flight Controller is an F722 FC featuring a BMP280 barometer, OSD, 500MB Memory Blackbox, a built-in FC LiPo monitoring system, and many more features.
    Add to Wishlist
    Add to Wishlist

    Description

    About this product

    The SpeedyBee F7 V3 Flight Controller is an F722 FC featuring a BMP280 barometer, OSD, 500MB Memory Blackbox, a built-in FC LiPo monitoring system, and many more features. Equipped with solder-free connectivity options, this FC is the perfect addition to your FPV build.

    VIDEO: SpeedyBee F7 V3 Flight Stack – Everything But The Kitchen Sink

    Features

    • 500MB Onboard Blackbox Flash memory
    • 8 Motor output perfect for X8 Cinelifters
    • 30.5 x 30.5mm Mounting Pattern
    • FC LiPo Monitoring System
    • Built-in Barometer
    • 4 LED Plugs
    • F722 FC
    • Buzzer
    SpeedyBee-F7-V3-Flight-Controller-Info 2024 Best SpeedyBee F7 V3 Flight Controller - Unleash Drone Potential

    Specifications

    • Power Output:
    • 1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A.
    • 2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A.
    • 3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
    • WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis.
    • I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc.
    • Support Flight Controller Firmware: BetaFlight
    • ESC signal M1 – M4 on the bottom side and M5-M8 on the front side.
    • LED: Used for WS2812 LED controlled by Betaflight firmware.
    • UART: 5 sets (UART1, UART2, UART3, UART4, UART6)
    • DJI Air Unit plug: A full DJI Air Unit JST slot onboard
    • BLE Support, used for Flight Controller configuration
    • Buzzer: BZ+ and BZ- pad used for 5V Buzzer
    • Mounting: 30.5×30.5mm, 4mm hole size
    • Dimensions: 41(L) x 38(W) x 8.1(H)mm
    • OSD: BetaFlight OSD w/ AT7456E chip
    • BlackBox: 500MB onboard data flash
    • BetaFlight Camera Control Pad: Yes
    • ESC Telemetry: UART UART4 RX
    • Power input: 3S – 6S Lipo
    • Target: SPEEDYBEEF7V3
    • SmartPort: Supported
    • Baro: BMP280 (I2C)
    • MCU: STM32F722
    • Boot button: Yes
    • RSSI input: Yes
    • IMU: BMI270
    • USB: Type-C
    • Weight: 9G

    Includes

    • 1x SpeedyBee F7 V3 Flight Controller
    • 1 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm – Yellow and Blue
    • 1x 6-Pin SH1.0 GPS module Cable without connector – 100mm
    • 1 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable – 30mm
    • 1 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable – 60mm
    • 1 4-Pin SH1.0 to 4-Pin JST1.25 FPV Camera Cable – 60mm
    • 1x 6-Pin SH1.0 GPS module Cable with connector
    • 1 4-Pin SH1.0 Radio Receiver Cable – 100mm
    • 1x SH 1.0mm 8-Pin Cable -30mm
    • 5x M3 8mm Silicone Grommets
    • 1x DJI 6-Pin Cable – 80mm